0 Talk to i9
  1. Home
  2. Learn
  3. Guides
  4. Professional streaming: SRT, NDI and encoders
8 min readGuide · Engineering

Professional streaming: SRT, NDI and encoders

A professional stream does not depend on luck with the internet. It depends on a well configured encoder, the right protocol for each leg and a backup path.

Key takeaways
  • The encoder compresses the video; the protocol carries it from one point to another.
  • SRT is the standard for carrying a signal reliably over the internet.
  • NDI is for the local network, between equipment in the same building.
  • RTMP and HLS are, in practice, the way into and out of the platforms.
  • Stable upload bandwidth matters more than peak speed.
On this page

Professional streaming is sending live video with broadcast quality and stability over the internet or IP networks. The core of the system is the encoder, which compresses video into a codec such as H.264 or HEVC, and the transport protocol, which carries that video to its destination. For legs over the internet, SRT is today the professional standard, because it recovers lost packets and keeps the signal stable. Inside a building, between cameras, switchers and computers, NDI carries video over the local network. Platforms ingest in RTMP or SRT and deliver to the audience in HLS.

The streaming and encoding page shows what i9TV delivers in permanent systems. This guide explains the pieces and how they fit together.

What an encoder does

An uncompressed HD video signal takes about 1.5 Gbps; 4K, close to 12 Gbps. No ordinary internet line carries that. The encoder compresses the video to a few megabits per second, keeping the visible quality. It can be a dedicated unit with SDI or HDMI inputs, or software on a computer.

  • Dedicated encoders: switch on and work, stable and built for continuous operation.
  • Software encoders: flexible, good for smaller productions, but dependent on the computer.
  • Contribution encoders: used by broadcasters to send signals between bureaus, with their own codecs and redundancy.
  • Bonded cellular transmitters: portable encoders that combine several mobile data networks, such as the bonded cellular backpack (mochilink).

Codecs and bitrate

H.264 is the most compatible codec and works on practically any platform. HEVC (H.265) delivers the same quality at about half the bitrate, which helps on limited links and in 4K, but needs compatible equipment at both ends. As a reference, a 1080p stream in H.264 uses between 6 and 10 Mbps; 4K, 20 to 40 Mbps. The streaming bandwidth calculator does the math with a safety margin.

SRT, RTMP, NDI and HLS: each on its own leg

The most common confusion is treating these names as competitors. In practice, they work on different legs of the chain.

  • SRT: carries the signal from the venue to the hub, the station or the cloud, over the internet, with loss recovery and encryption.
  • RTMP: an old, simple protocol, still the ingest for most platforms.
  • NDI: carries low-latency video over the local network, between cameras, switchers and computers.
  • HLS: delivers video to the audience in chunks, adapting quality to each viewer's connection.

The SRT vs NDI comparison goes deeper into the difference between the two protocols most used in production.

Why SRT became the standard

SRT (Secure Reliable Transport) was created to carry quality video over networks that lose packets, such as the internet. It resends what was lost within a configured time window, the latency. The worse the network, the higher the latency needed. It is open, free and supported by most professional encoders, decoders and platforms. For broadcasters, it means receiving signals from bureaus and remotes without a dedicated link.

NDI in production

NDI turns the local network into video infrastructure. A PTZ camera with NDI sends pictures, receives commands and receives tally over the same network cable. Graphics, playback and remote call computers go into the switcher without capture cards. For mid-size productions, podcast studios, churches and video radio, NDI simplifies installation a lot. In broadcasters with large facilities, the standard is usually SMPTE ST 2110.

How to build a stable outbound feed

  1. 01
    Measure the real networkTest the upload at the venue, at broadcast time, for at least half an hour.
  2. 02
    Choose codec and bitrateUse a bitrate of no more than half the measured stable upload.
  3. 03
    Use SRT on the internet legSet the latency according to the network quality.
  4. 04
    Have two pathsA second line through another carrier or a bonded cellular transmitter, with automatic failover.
  5. 05
    Distribute in the cloudSend one signal and let a service distribute it to several platforms.
  6. 06
    Monitor the destinationOne person watches the stream the way the audience sees it, to catch problems fast.
In practice

Set the encoder to constant bitrate with a two-second keyframe interval. Most platforms ask for it, and the signal arrives more predictably.

Latency: how much delay is acceptable

The whole chain adds delay: encoder, network, platform and the viewer's player. On public platforms, 10 to 30 seconds is common. For live interaction, such as audience questions or auctions, it pays to turn on the platform's low-latency mode. Between a remote and the station, with well tuned SRT, the delay stays at a few seconds or less, which allows conversation between studio and reporter.

Streaming in churches, radio and companies

Outside broadcasters, professional streaming has become routine. Churches stream services every week, radio stations take the studio to video and companies run internal live events and launches. In these cases the system is permanent: a dedicated encoder, contracted internet with guaranteed upload, a second path and a simple routine that volunteers or the communications team can run. See what goes into a live service streaming system.

Streaming with i9

i9TV designs and installs streaming and encoding systems for broadcasters, churches, radio stations and corporate studios, integrated with the control room and the network. For events, i9 Studios handles the outbound signal as part of the live broadcast, and the rental catalogue includes professional encoders and decoders. Tell us where the signal starts and where it needs to go, and get a streaming proposal with the main and backup paths.

Want help with this?

i9 does this every day: production, broadcast, engineering and equipment, with one team accountable from start to finish.

Frequently asked questions.

What is the difference between an encoder and a decoder?

The encoder compresses video for sending; the decoder receives and decompresses it at the destination. In a feed between a remote and the station, there is one at each end.

Does SRT work with YouTube?

YouTube accepts RTMP ingest and other protocols in certain configurations. Many productions use SRT up to the cloud and from there send to each platform in the protocol it accepts.

Do I need a dedicated encoder or is software enough?

For simple streams, software works. For continuous operation, important events or feeds to broadcasters, dedicated encoders are more stable and predictable.

Does NDI work over the internet?

NDI was built for the local network. To carry video over the internet, the most common path is SRT, or tools that convert NDI to a transport designed for the internet.

What internet do I need to stream in 4K?

Somewhere between 40 and 80 Mbps of stable upload, depending on the codec and bitrate chosen, with a second backup path.