0 Talk to i9
  1. Home
  2. Learn
  3. Guides
  4. Satellite broadcasting: how it works
7 min readGuide · Engineering

Satellite broadcasting: how it works

In satellite broadcasting, an earth station sends the signal to a geostationary satellite, which sends it back down over a huge area. Here is each stage, the bands used, the limits and when satellite is still the best choice.

Key takeaways
  • The signal goes up from the ground to the satellite (uplink), is repeated by the transponder and comes down to the dishes (downlink).
  • TV satellites sit in geostationary orbit, about 36,000 km from Earth.
  • C band holds up better in rain; Ku band uses smaller dishes.
  • The round trip to the satellite adds about a quarter of a second of delay.
  • Satellite reaches many points at once, where there is no fiber.
On this page

Short answer

Satellite broadcasting works in three stages. An earth station encodes the video and audio signal, modulates it and sends it through a dish to a geostationary satellite: that is the uplink. On the satellite, a transponder receives the signal, shifts its frequency, amplifies it and sends it back to Earth. On the way down, the downlink, any dish pointed at that satellite inside its coverage area picks up the signal and a receiver decodes it. Because one satellite covers an entire continent, a single uplink reaches thousands of points at once.

Geostationary orbit

TV satellites sit in geostationary orbit, about 35,786 km above the equator. At that height, the satellite circles the Earth in the same time the Earth takes to rotate, so it appears fixed in the sky. That is what lets you point a fixed dish and never touch it again. Each satellite occupies an orbital slot, identified by longitude, and dishes in Brazil point at slots that cover the continent.

The signal path, stage by stage

  1. 01
    EncodingThe video is compressed by an encoder, in standards such as H.264 or HEVC, and the audio is encoded with it. Several programs can share the same stream.
  2. 02
    Modulation and encryptionThe stream is modulated, usually in DVB-S2 or DVB-S2X, and can be protected with encryption, such as BISS, so only authorized receivers can open the signal.
  3. 03
    UplinkA power amplifier and a dish send the signal to the satellite. The station can be fixed, a teleport, or mobile, such as a satellite truck or a flyaway antenna.
  4. 04
    TransponderOn the satellite, the transponder receives the signal, shifts its frequency so it does not interfere with the uplink, amplifies it and sends it back to the coverage area.
  5. 05
    Downlink and receptionDishes on the ground pick up the signal. A professional integrated receiver decoder, the IRD, demodulates it, decrypts it and delivers the video to master control or to the transmitter.

Frequency bands: C, Ku and Ka

  • C band: downlink between 3.7 and 4.2 GHz and uplink between 5.925 and 6.425 GHz. Little affected by rain, but needs larger dishes. The traditional band for distributing signals between broadcasters.
  • Ku band: downlink between about 10.7 and 12.75 GHz and uplink near 14 GHz. Allows smaller dishes, which suits trucks and flyaway antennas, but loses signal in heavy rain.
  • Ka band: even higher frequencies, widely used for satellite internet. More capacity and more sensitivity to rain.

In Brazil, the arrival of 5G in the 3.5 GHz range, next to C band, pushed free satellite TV reception by home dishes to move to digital Ku band, with new dish and receiver kits for households.

The limits of satellite

  • Latency: the signal travels about 72,000 km up and down, adding close to a quarter of a second of delay. In live interviews with a reporter on location, that delay shows in the conversation.
  • Rain: in Ku band, storms can degrade or cut the signal for a few minutes. More uplink power and margin in the design reduce the risk.
  • Sun outage: twice a year, near the equinoxes, the sun passes behind the satellite as seen from the dish, and the noise can interrupt reception for a few minutes a day.
  • Capacity cost: transponder space is contracted by bandwidth and time, on a full-time contract or as occasional use.
  • Line of sight: the dish must see the satellite with no buildings or mountains in the way.

Where satellite is used in TV

  • Network distribution: the originating station sends programming to the master control of affiliates and repeaters across the country.
  • Event contribution: satellite trucks and flyaway antennas bring the signal from a game or a news story to the broadcaster.
  • Direct reception: satellite pay TV and free-to-air home dishes.
  • Remote regions: where there is no fiber and no good cellular coverage, satellite is often the only path.

Satellite, fiber or the internet

Today satellite shares the work with fiber and the internet. Fiber has low latency and lots of capacity, but it has to reach the site. The internet, with protocols such as SRT and bonded cellular backpacks (mochilinks) that combine several cellular connections, is cheap and quick to set up, but it depends on the network available. Satellite is the choice when the signal must reach many points at once, when the site is remote or when you want a backup path independent of terrestrial networks.

In practice, serious operations combine paths. A station can receive the network feed by satellite and by fiber; an event can uplink by satellite with a bonded cellular backup. The guide remote production (REMI) shows how these paths change the way you produce.

In practice

When you book satellite capacity for an event, also book a line test before the broadcast and confirm the exact parameters with the receiving side: satellite, frequency, polarization, symbol rate and encryption key.

How i9 works with satellite

i9TV designs and integrates satellite uplink and reception systems inside broadcasters and technical centers, with dishes, receivers, encoders and monitoring tied to master control.

At Freedom Air TV, in South Africa, satellite transmission was integrated with two switchers and the master control of a complete station with three interconnected studios.

If your operation needs satellite, fiber or internet links, the systems integration team designs the path with a backup.

Want help with this?

i9 does this every day: production, broadcast, engineering and equipment, with one team accountable from start to finish.

Frequently asked questions.

What is the difference between uplink and downlink?

Uplink is the signal going up from the earth station to the satellite. Downlink is the signal coming down from the satellite to the receiving dishes. They use different frequencies so they do not interfere with each other.

Why does satellite transmission have a delay?

Because a geostationary satellite sits about 36,000 km up. The signal goes up and comes down, which adds close to a quarter of a second, plus encoding time.

Does rain knock out a satellite signal?

Heavy rain can degrade or cut the signal, mainly in Ku and Ka bands. C band suffers much less. Power margin and properly sized dishes reduce the problem.

What is an IRD?

It is the professional receiver decoder used by broadcasters. It receives the satellite signal, demodulates it, decrypts it and delivers video and audio to master control.

Is satellite still worth it with so much fiber and internet?

It is for distribution to many points, for remote sites and as a backup path independent of terrestrial networks. For a single point with fiber available, fiber is usually better.

Does i9 integrate satellite at broadcasters?

Yes. i9TV integrates satellite uplink, reception and monitoring at broadcasters and technical centers, tied to master control.